Posted by John C on in Disability Retrofits | Comments Off
Make a difference in the community when you contribute to The Western Australia Contractors & Tradespeople Association for Disability Retrofits Foundation, a nonprofit organization in WA. We are a not-for profit organisation providing advice and information to Persons with Disabilities. We are here to help you find a Contractors & Tradesman for Disability Retrofits in Western Australia . Locating a pre-screened Contractors & Tradesman (one that needs to do the work, in the period of time you need it done) is always difficult. The procedure is simplified by our service. You submit a request for a free quote and we supply you a quick answer, usually within hours. (Free of charge)
If you wish to contact us while our site is under construction, please dont hesitate. Ph/Fax: 1800 9995 660 – Mobile: 0311 576 276 email: [email protected]
Posted by John C on in Handrails for the Disabled | Comments Off
image courtesy of : www.humanrights.gov.au
Many modern handrails were created to help those with ambulatory impairments, especially blindness and specific impairments. The Australians with Disabilities Act The Building Code of Australia establishes specific structural parameters to which many public and commercial places must conform to be completely accessible to individuals with physical handicaps. Among those parameters covers positioning and the layout of including grab bars, handrails. Used in several houses, handrails aren’t restricted to public places. But most grab bars and handrails found in private settings may also be made to meet The Building Code of Australia standards
For grab bars and handrails to meet with The Building Code of Australia standards, public need to have the ability to resist a specific amount of pressure. But handrails and some grab bars (see www.balustradeauthority.com) made to be used in-house use are manufactured from PVC pipe or reinforced nylon.
The most frequent forms of handrails are those used for wheelchair access ramps and pathways, stairs. These railings go along paths parallel to incline or the earth. It’s not unusual for all these railings to enter shades or vibrant shades that contrast the backdrop. Additionally, these kinds of The Building Code of Australia railings will most likely have Braille signage at every end, showing destination and the location of the railing.
There is a grab bar a shortened handrail, used mainly in toilets to help disabled persons. Bathroom grab bars are very common but can even be set up in a disabled person’s residence. These bars normally sit next to the bathroom on both sides or one, letting the handicapped person. Similar grab bars are manufactured for baths and showers. A grab bar’s purpose is generally to assist in movement and support in private scenarios where a wounded or disabled man is not likely to want help from a different individual.
There are a number of mobile grab bars in the marketplace that use suction cups at every end to stick to some surface that is smooth. These aren’t designed as they’d be unable to satisfy with the stress conditions, using suction cups. But these help people that have moderate impairments or people who travel a good deal.
Used mainly in hospitals, particularly psychiatric wards, these railings possess a sheet that goes to an adjoining wall in the interior of the railing. This helps to ensure that patients cannot tie anything with which to hang themselves around the railing.
Shower seats are ADA grab bars that are related to and so are usually manufactured from a substance that is similar. Shower seats usually have a grab bar that is built in or nearby.
Posted by John C on in Blog, Maintenance, Tradesmen | Comments Off
It’s the new service protecting seniors from being ripped off by dodgy tradies. The tradesmen are reliable, the work is honest and it’s dirt cheap.
The Commonwealth Home and Community Care (HACC) Program provides funding for services which support frail older people and their carers, who live in the community and whose capacity for independent living are at risk of premature or inappropriate admission to long term residential care.
Older people are people aged 65 years and over and Aboriginal and Torres Strait Islander people aged 50 years and over.
For more information, phone the Aged Care Information Line on 1800 200 422.
Source : http://aca.ninemsn.com.au/article/8529215/protecting-pensioners
Posted by John C on in Mental Health | Comments Off
There’s no one universally accepted definition of pressure. In the
Australia, for instance, the National Institute for Occupational
Health and Safety ?1999? defined work-related anxiety "as
The dangerous psychological and physical reactions that happen when the
Demands of the job don’t fit the abilities, resources,
Or needs. Occupation strain can cause poor health and even
Harm." In The Sutherland Shire of NSW, Mental Health Commission of NSW see more here ?1999? Said "pressure is the reaction people have to excessive
pressures or alternative demands put on people." The Australian Government
Comcare ?2008? defined work-related anxiety as "a kind
Of stress, a state of arousal, and negative emotions experienced in
Relationship to the work function."
There exists a should come up with a better understanding of how
Pressure is experienced in the building industry, the procedures by
Which it may be minimized efficiently or ameliorated and the
Variables that predict why some professionals experience stressrelated
States? Edwards 2005 and Love?. A theory
provide some insight into these problems is the Lazarus and Folkman1984? theory of anxiety assessment. Lazarus ?1991? Supplied a conceptualization
of pressure that focused on work-related stress as a
Procedure, affecting a trade between a person and their
work environment. Based on Lazarus and Folkman ?1984?,
This pressure is cyclical and completely recursive in the results of
the pressure procedure ?strains? Possess the potential to affect future
Results by depleting the or by becoming added resources
Managing resources and skill supports that exist to the
Person. In conditions that are serious or constant, stress can lead
To mental ill health, which affects farther on anxiety and
Stress. Thus, pressure is a circular and always transforms
Procedure that consists of stressors ?i.e., the state that causes
Stress physically?, consequences, and resources, which raises important
Consequences for measurement and Treatment
Lazarus and Folkman ?1984? proposed the subjective assessment
by a person makes their scenario essential to their own wellbeing.
A scenario is unable to be considered trying until the
Person has identified it as such. Stressful conditions are
those appraised as threatening or dangerous to the person, and
those that the person considers they’ll be unable to handle
or control. Thus tension resides in the man nor workplace,
but is a reflection of the individual’s exceptional result to their
Conditions. In compliance with all the pressure-procedure definition,
Work pressure was described as an incompatibility
Person as well as their work environment which is perceived as trying
The most critical stressors identified by building supervisors
have been work overload, role ambiguity and conflict, outstanding
Overtime the varied variety of prohibitive career advancement,
Characters encountered in their own work environment, traveling,
Shifting technology, redundancy, customer demands, small resources,
Fiscal pressures, budget solving little, and constraints
But pressing and Davidson and irksome issues?Sutherland
1989; CIOB 2006?. Based on Langford and Sommerville
?1994? the common factors behind anxiety may be categorized as the physical
environment, the organization the physical, the manner in which work in
Handled, the person’s job the relationships together with the organization,
Inside the corporation, societal and private relationships,
Gear, and stress that is individual.
Posted by John C on in Uncategorized | Comments Off
Balustrades, Handrails & Stairs
There is a balustrade an upright up stand which shields users of a building next to a perpendicular displacement between flat building surfaces or in the side of a stair. Balustrading is required be stiff enough to resist applied pressure and to obey the BCA. Balustrade could have a handrail over.
To stop individuals from falling, a constant balustrade or obstacle should be supplied alongside any staircase or
image courtesy of : www.build.com.au
ramp, any flooring, corridor, hall, balcony, verandah, mezzanine or trail of entry to a building if it isn’t bounded by a wall or some level more than one m above adjoining flooring or finished ground level. It’s vital that you be aware the measurement of the height of obstacle or the balustrade is from the finished flooring surface. Finishes such as carpeting and ceramic tiles can make an important difference to the finished floor height.
The Height of Obstacle or a Balustrade ustn’t be Less Than
- A transition zone could be included where the obstacle or balustrade height changes from
- 865mm in ramp or the stair flight to 1m in the landing.
To Comply with Requirements of Acceptable Building Training Stairs must not Have
- So that people can rest more than 18 risers in a flight of steps to make sure that they manage a limited amount of measures before a landing is installed
- 1:8 should not be exceeded by the most gradient of a ramp and the flooring surface must be non slip.
Obstacles or balustrades ought to be built such that a man cannot fall over or through them while at the exact same time limiting a kid crawling through them. Openings in obstacles or balustrades should be built so that any opening doesn’t allow a 125mm sphere to pass through it where above the nosing line this space is examined for stairs.
A barrier ought to be powerful enough to resist failure should a man fall or lean against it. A balustrade or obstacle has to be made to take loading forces in accordance with AS 1170.1 which demands that a balustrade or obstacle should be structurally sufficient to resist a point load of 0.6kN and an equally distributed load of 0.4kN used inward, external, or down on the handrail. These design loads are meant to make sure that the obstacle is stiff enough to resist a man falling against it without failing (point load) and stiff and powerful enough not to fall should individuals lean against the obstacle (distributed load). The handrail also has to have the ability to resist wind loads especially where there is a solid panel used.
In wetness or weather exposed infil, handrails, posts, newels, balusters and uses should be naturally long-lasting Class1 or Class2 lumber species including ironbark, spotted gum, blackbutt, jarrah, merbau, or kwila with any sapwood present. Instead, preservative ought to be treated to higher or H3 standard and should comply with AS 1604. Ideally, the lumber be straight and ought to be free of any important strength reducing characteristics.
All metal connectors including mounts, screws, bolts and nails ought to be at least hot or for Class 3 corrosion resistance screws, as per AS3566. For coastal settings subject to airborne salts deposit, equal corrosion resistance alloy connections or stainless steel ought to be utilized.
Nail holes ought to be stopped with outdoor grade wood filler. Some loose stuff or soil ought to be removed ahead of coating. Two closing top coats of exterior paint or stain should subsequently be used in accordance with manufacturer’s recommendations.
For floorings more than 4m above ground, any flat components within the balustrade or obstacle between 150mm and 760mm above flooring should never ease scaling. To keep this from happening the balustrade be a solid panel obstacle or should have vertical members spaced no more in relation to the maximum opening.
Handrail and Barrier Heights mustn’t be Less Than
1m over the ground entrance trail, balcony or landing
A transition zone could be included where the obstacle or balustrade height changes from 865mm in the stair flight or ramp to 1m in the landing
Posts should be spaced at 1.8m
Wire has to be stainless steel using a minimal diameter of 3.2mm
Intermediate droppers must be matched at a maximum 9oomm between posts and guaranteed top and underside
Tensioners can be set at every change of direction of 30 degrees or more on each strand of wire
A stable handrail is needed of steel tube using a minimal diameter of 40mm or lumber in accordance with the Timber framing Code AS 1684.2 1999.
Posted by John C on in Flooring | Comments Off
Wondering which type of flooring to utilize in your house? It is a major choice because not all forms of flooring are appropriate in all rooms.
The cost of carpet flooring still the most efficient kind of flooring to update or replace while it changes. It gives off a soft appearance to a room and feels soft. Carpet flooring is, in addition, not noisy to walk on, so there is no. If you are trying to find an affordable, simple- to-install choice, go for carpeting.
There are drawbacks, however. First, upkeep may be an issue carpeting flooring gets stained and collect filth, because when vacuumed and shampooed frequently. There are stain-resistant carpets accessible, but they aren’t immune to spots. More to the point, carpeting shouldn’t be used by you if someone in your family has allergies.
Marble, for example, seems amazing but is slick when wet. Porcelain is immune to spots and moisture, but is not easy to cut up. Due to this, you need to consider the kind of tile where it’d be put and to be used.
Tiles are not usually soft unless you are barefoot, to walk on. When they break, they can not be easy to fix. Specific tiles are slick when wet, like granite and marble. Tiles like limestone and terracotta should be glazed to shield it from water. Having a tile flooring is likely to allow it to be even colder if you reside in cold weather.
Try vinyl if you’d like a low-cost alternative. It is simple to set up and clean; immune to scrapes, spots and water; and it could be made to look like stone, ceramic or hardwood like other sorts of flooring. Unlike hardwood or tile, vinyl feels soft. It is hot either.
It is also catchy to fix, and the versions that are more affordable tend to discolour. Vinyl flooring may be put in rooms that do not need softer padding like kitchen, laundry room or the veranda.
Seeking flooring that is environment friendly? Contemplate attempting cork. It is not difficult to wash, water- and stain-resistant, consumes noise, and is a great insulator. In addition, you have to reapply the price’s wax finish each year.
This kind of flooring is rough, a cinch to wash and preserve, and resistant to spots and scratches –even for those who own a pet in the home. When it is ruined by you, it can not ever be refinished.
Wood is a resistant, long lasting form of flooring that is simple to wash and preserve. On top of that, it seems amazing and may be refinished.
Posted by John C on in Blog, Concrete | Comments Off
Underneath is a step by step guide on the best way to pour concrete.
Measure #1: Make a strategy
Like every significant job that is DIY, you must plan for your concrete as it is incredibly hard to correct in the event that you make a blunder, placing job. You should assess the space you want to concrete over. In addition, you have to take into account other variables like foot traffic, and disposition, weather, amongst others.
Measure #2: Prepared the materials
In the event you are coping with a tiny region, you can simply buy pre-mixed concrete. For bigger regions, it’d be more cost effective should you get the materials independently and then combine others yourself. While there are various kinds of pre-mixed concrete, look for the ones which are suited to residential jobs. As part of your materials checklist, do not forget to include the following:
- Timber boards
- Cord and wooden pegs
- Fibreboard strips
- Contractor’s square
- Spirit level
- Scoop and spade
- Polythene sheeting
#3: Prepare the foundation
Dig to the depth you want to fill with concrete, when you are done. Keep in mind that the foundation needs to be larger by 75mm to 150mm in relation to the finished slab.
Step #4: Set up the formwor
Put the lumber boards against the wooden pegs and align them correctly using the cords. Make use of the spirit level to see whether the very top of the formwork is with the concrete. Ultimately, nail the boards to the wooden pegs so the concrete would not ooze out and ensure there are not any spaces in between them.
Measure #5: Combine the concrete
It will be wise to employ a power mixer, in the event you are working on a big region. For smaller jobs, you can combine your concrete. Only see that you won’t mix concrete on soil; use a wooden plank instead.
To the plank using a spade, measure the proper quantity of every substance, stack a bucket with it, and combine the stuff until the colour is uniform. Dig a hole in the middle out, add some water, then turn the mixture over several times until everything is damp, and push in the concrete mixture into the small moat.
Step #6: Pour and level the concret
Pour into the formwork and distribute the mixture equally using your spade. In the event you are placing concrete over a place broader or longer than 4 metres, part the formwork into several sections using fibreboard strips to stop the concrete from cracking. Ensure all places in the formwork are correctly filled with no spaces in between.
Eliminate as essential.
Measure #7: enable the concrete to place
Cover with all the polythene sheeting. Wait for a complete day before removing the formwork.
Posted by John C on in Veranda in NSW | Comments Off
Need to make your lawn beautiful? Subsequently contemplate building a veranda–with materials and the appropriate tools, it may not be somewhat difficult. Here’s how:
Measure #1: Layout the layout
You first should prepare a layout of the veranda. Afterward a rectangular layout would have been a great design to begin with if that is your first DIY job. Using complex shapes with unusual angles or curves would need specific tools like masonry saws, which will cost you more cash.
Measure #2: Look for a place that is suitable
Then, you should discover an excellent site where the veranda would stand. Here are some factors:
Anything more than this and you’ve got to rank (i.e. increase the amount) the surrounding region.
Obstacles: prevent building under trees; tree roots could be damaged by any digging. And do not forget to call your utility suppliers and ask about any hidden lines in the region before digging.
Height: avoid low places where water can collect.
Shadiness: the veranda could be outside, but if you don’t would like to bask under the warm sunshine in any respect times, find a shaded space. Add plants that could supply some cover whether there are none.
Here are the materials you will need for the veranda:
- Landscaping sand
- Handheld or gasoline-powered tamper
- Landscaping material
- Landscaper spray
- Paving stones
- Cord and stakes
- Landscaping flagstone (this will probably serve as the edge of the veranda)
- Tape measure
- Flat scoop
- Rubber mallet
Measure #4: Mark the place
It is time to indicate the layout of the veranda in the earth. Drive the stakes into the earth and then tie the cord around each stake. For those who have landscaper spray, indicate the earth directly too.
You can hire an excavator or set the soil for another project in a dumpster if you don’t want to make use of it.
Next, you put the landscaping material over the excavated area. Allow the material stretch for at least 6 inches over the borders of the veranda, then make use of the stakes to hold it in place. It’s possible for you to cut the material later after setting the borders of the veranda.
Ensure the region is level, and put a 2-inch layer of sand to maintain the paving stones.
Measure #6: Place the edge
Once the base layers of the veranda are set, it is time to set the rock boundary. Not all rocks would most likely possess the same depth thus make use of the sand to correct the height of the rocks. When the rocks are level by using your rubber mallet them flat.
Add another tier of sand in the region encompassed by the boundary, subsequently screed the sand before putting the paving stones. When you tamp on the paving stones, they’ll be degree with the border stones.
Then tamp the veranda again when all the paving stones are spread sand over the veranda using a sweeper to fill each of the crevices between the thinner ones.
Posted by John C on in Portfolio | Comments Off
While I read this it pissed me away !! It demonstrates how greed can change you no matter where your home is and what states you’ve got to survive..
You’re a seasoned handyman metal worker in Central America who has been comparatively successful in the business.
He shifted his company and started assembling wheelchairs in his store, when the child learned of proper wheelchair designs meant to be built and used in developing countries. Since that time his son had embraced and enhanced a layout developed by Whirlwind Wheelchair International from Australia. And this store now employs 10 wheelchair passengers as developing learn useful abilities assembling seats.
His organization is so supplying vocational training for disabled people, value added economic action, and wheelchairs that function well and hold up in the rough conditions they’re exposed to in your state. Disabled work 10 months annually, giving the ability to create 300 seats annually.
Now for the BS Component !! You understand that Mr. Moneybags is somehow related to handicap support in developing countries.
Yet, in the past your only encounter with folks like Mr. Moneybags is that they dump them on the marketplace at really low costs and import low quality seats. This drives the cost down to a point where you are unable to sell your seats and endangers there the employment of the workers and business. Sadly, since they can be made abroad with procedures and distinct parts, it’d generally cost more to repair them than to construct a brand new, higher quality seat. His seats enable a passenger considerably more freedom of movement on the rough terrainin substantially of the state and will usually continue at least under significant use.
This enterprise to me is a win, win scenario for the workers as the work who learn Tell me your idea, I’m in a wheelchair and I understand the worth of a great one.
Handicap Adjustments provides an end to end building service, utilising over 25 years specialist expertise and a variety of abilities and abilities within our team.
- Servicing public and private buildings
- Including offices, houses, hospitals, aged care facilities and other facilities
- Long-lasting or temporary constructions, alternatives and alterations
Alternatives and various alternatives for one off occasions, scenarios that are temporary (including healing and recuperation), and long-term facilities
Interior and outdoor works
A handicap access and freedom balustrade that is compliant facilitates circulation As part of the BCA codes, handicap accessibility and freedom balustrades that are compliant use handrails that are uninterrupted, making them suitable and simple for everyone to grab and move through spaces unimpeded. Freedom and handicap accessibility are critical to the legal and successful functioning of a space.
Conforming to these codes empowers greater access for the disabled and easier flow. Each of the balustrades holds and creates a feeling of movement.
Plumbing Solutions Disability Aids specialises in repairs, pipes comforts, availability, renovations and security fixtures for handicapped and the aged.
Friendly local pipes team has 20 years’ expertise in the South-East Queensland region, and can cover any complex care or building need, including availability aids, disabled toilets, commercial toilet renovations, kitchen alterations, security mechanics and other conveniences.
Covering the whole Brisbane to Gold Coast area and based in QLD, we work with aged care, health care and medical facilities throughout South-East Queensland. No job is little or too large, and we can accommodate to any condition that is specialised.
- Handicapped toilets (practices, offices and houses)
- Simple accessibility handsfree detector faucets and tapware
- Specialised toilets, seats and pans
- Security fixtures
- Kitchen renovations and alterations
These links will take you to publications that have great wooden ramp preparation and construction guidance:
Wood Ramp Design and Construction Manual
Wood Ramp Design – NC State University
This isn’t a beginner-level construction job. Everyone who uses the ramp’s security is at position, so the ramp must be made of the finest materials and built according to all local building codes.
Here are some ramp construction hints:
- If you begin with treated lumber the ramp you assemble will continue much longer and need less care.
- Use fasteners that are treated for outside use. The fasteners defined to be used in decks and fences will work good.
- Nonskid paints and adhesive grip tape are popular for slide-proofing wood ramps. Sadly, they just work for a brief period of time before they should be reapplied and fail.
An alternative that is much better are the new aluminum nonskid tread strips. They’re not difficult to install and last a very long time.